THIS POOL IS NOT DESIGNED FOR DIVING OR JUMPING.DANGEROUS INJURY CAN RESULT-SHALLOW WATER!!!MATRIX OVAL YARDMORE POOL INSTRUCTIONSWARNING:Your pool is
STEP 8 – PRESSURE PLATE INSTALLATION:Place one 44" pressure plate on each strap end channelso that the center of the plate is even with the cente
STEP 10 – SQUARING THE STRAIGHT SIDES:Now that the base of the pool is fullyassembled, make sure that the straight sides of thepool are perfectly in l
12STEP 12 – LEVELING THE CURVED SIDES:The next step is to level the curved sides of the pool. Before doing this you may want to measure the overalllen
STEP 14 – WALL INSTALLATION:*** DO NOT ATTEMPT THIS STEP IN WINDY CONDITIONS. THE WALL IS VERY HEAVY AND EXTREMELY DIFFICULT TO MANAGE ON A WINDY DAY.
STEP 16 – PREPARING THE COVE:Using neutral alkalinity sifted earth or fine sand without pebbles, build a 2" base over the entire pool area toprot
STEP 17 – UPRIGHT INSTALLATION:Install upright by simply lining the upright up to the three clips in the bottom of the cuff and pushing downuntil all
STEP 18 – LINER PREPARATION:After cove and base are in place, tamp and rake the entire pool area. Make sure that no sand remains onthe wall above the
STEP 19 – HANGING LINER AND COPING INSTALLATION: *** FOR OVERLAP LINERS ONLY! IF YOU HAVE A BEADED OR A J-HOOK LINER SEE SEPARATE INSTRUCTIONS WITH L
STEP 20 – LINER ADJUSTMENT: (FOR OVERLAP LINERS ONLY)Once the liner is held securely in place by coping, temporarily pull wrinkles in the floor toward
STEP 21 – TOP WALL RIM INSTALLATION: DetailWhen you are completely satisfied with the way that your liner is hanging, you can now permanently installt
Actual size of pool.Space needed for installation.YARDMORE POOL SIZES18'10"17'16' 10"12 x 1712'32'20'4"30
STEP 22 – TOP WALL RIM INSTALLATION: Lay-OutWhen the liner is completely adjusted and the plastic coping is secured (if an overlap liner) the next st
STEP 24– TOP RAIL INSTALLATION:You should have two different size top rails with your oval pool. The short top rails (measured from longestpoint to lo
STEP 25 – INSTALLING THE TOP CAPS:22Center a top cap on each upright one at a time. Angle the front of the cap (the wider half of the cap whichgoes to
FINAL INSTALLATION TIPS: When installing a thru-the-wall skimmer, follow the instructions of the manufacturer. It is essential that there isno leakage
IMPORTANT WINTER RULES: After pool has been winterized and ALL steps carefully followed, the following checks and proceduresMUST BE strictly followed
INTRODUCTION:Congratulations on becoming the owner of a new Sharkline above ground swimming pool. This is theinstruction packet for installing your sw
STEP 1 – PREPARING THE SITE:Refer to the “true size” diagram on the second page to see the dimensions of your swimming pool. Once youhave these measur
STEP 2 – LEVELING:Once you have designated the space for installation including the extra space and have cleared away the sod inthat area, you can beg
Once you have completed the ground preparation, you shouldopen all cartons to the pool and become familiar with all of itscomponents. You should also
STEP 5 – PRE-ASSEMBLING THE STRAIGHT SIDES OF A YARDMORE OVAL POOL:A) Start by laying out the under box channels so that the open sides of each under
STEP 6 – STRAP ASSEMBLY FOR YARDMORE OVAL POOLS: When you separate the strap pieces, you will find that you have two different lengths. You will have
STEP 7 – STRAIGHT SIDE LAYOUT:After all of the straps have been fully assembled and attached to the strap end channels you can now start toset them up
Commentaires sur ces manuels